If you're having issues with the rear iSight camera in your iPhone 5c, it's possible a replacement could fix the issue. A bad rear camera assembly could have many different symptoms. The most common is spots or purple haze showing up in photos. If the spot is always in the same place, the assembly is defective. If the shutter won't open or your Camera app freezes, that could also indicate a bad camera. Other symptoms include lines through photos, hazy or unfocused shots, and blacked out photos showing up in the Photos app. Luckily a camera replacement in the iPhone 5c isn't terribly difficult. We can walk you through how to get replacement parts and how to perform this relatively easy iPhone repair all on your own! The best part? It'll cost a fraction of what a new iPhone would cost!
What you need to replace an iPhone 5c iSight camera
You'll need some tools and parts in order to repair your iPhone 5c. If you're in the United States or Canada, we highly recommend checking out eTech Parts as we've had lots of good experiences with them and know their customer service is out of this world. All the links below will route you to the direct item you need on eTech's site.
iSesamo Opening tool (not necessary but awesome for prying up cables and getting under adhesive) - Buy Now
1. Power off your iPhone 5c
Before performing any repair on any iPhone, iPad, or iPod touch you should always remember to power it off. Simply hold down on the Power button until you see Slide to Power off. One you're sure your iPhone is turned off, proceed to the next section.
2. Remove the two security screws on both sides of the dock connector
There are two security screws that secure the screen to the frame and they sit on each side of the dock connector. Use your 5-point security screwdriver to remove them. They are both the same size so it's okay if you mix them up.
3. Remove the display assembly
Place your suction cup slightly above the Home button assembly and secure it to the screen.
Holding the iPhone in place with one hand, gently pull upwards on the suction cup until you free the bottom of the screen. You should now be able to use your fingers to slowly raise up the screen and expose where the front assembly is connected to the logic board.
Remove the four screws holding down the shield that covers the display cables. To do this, use your #000 screwdriver. These screws are different sizes so make sure you keep them organized in a way you can remember for re-assembly.
Once all four screws are removed, carefully remove the shield and set it aside.
Now use your spudger tool in order to remove the three cables shown in the image below.
The display assembly should now be free from the body of the phone. Go ahead and set the display assembly aside.
4. Disconnect the battery
We don't need to completely remove the battery for this repair but it's always a good idea to disconnect the battery before removing and replacing internal components in order to prevent a short from occurring.
Remove the two screws holding down the battery cable using your #000 Phillips screwdriver.
Gently lift the battery shield out of your iPhone 5c and carefully set it aside.
Use your spudger tool to carefully pry up the battery cable.
5. Replace the rear iSight camera
Use your #000 Phillips screwdriver to remove the two screws holding the camera assembly and shield in place.
Use the flat end of your spudger tool to pop up the single connector holding the camera assembly to the main board.
Lift the camera assembly and shield straight out of your iPhone 5c.
The silver metal shield should easily come off your iPhone 5c's old camera if pulled lightly.
Peel off any protective backing on the new camera assembly. Take care not to touch the lens and don't get dust in the camera recess of your iPhone 5c or you'll have to remove it and clean it later.
Place the new camera assembly into your iPhone 5c. Take care not to shove it and take note of the cable fold in the old camera assembly as you may have to create the fold yourself on the new assembly.
Replace the metal shield over the new camera assembly.
Replace the two screws you removed in step one using your #000 Phillips screwdriver.
6. Re-connect the battery
Re-connect the battery cable that you pried up earlier.
Replace the battery cable shield.
Replace the two screws holding the battery cable down using your #000 Phillips screwdriver.
7. Re-connect the display assembly
Carefully reconnect the three cables running from the display assembly to the logic board.
Reposition the metal shield that sits over the three cables and replace the four screws that hold it in place, remembering where each one came from — they are all different sizes.
Line up the top of the screen carefully and make note of the teeth that line up to the top of your iPhone 5c's frame. Once the top of the display is lined up, carefully snap down the remainder by moving your fingers along the edge.
8. Replace the security screws on each side of the dock connector
Once you are confident that the display is seated correctly again, use your security screwdriver in order to replace the two screws on either side of the dock connector.
9. Test the new iSight camera
It's now safe to turn your iPhone 5c back on. If all went well, you should see an Apple logo. Once your iPhone finishes booting up, perform the following steps to verify the new iSight camera is now working properly:
Snap a photo of a white piece of paper or surface and check for discoloration and spots
Snap a photo of a black piece of paper or surface and check for discoloration and spots again
Toggle between the front facing and rear camera to make sure they behave and function normally
Take a photo with the flash on to ensure the flash functions properly
Test out other camera modes and try recording a short video and make sure audio comes through properly as well
Test FaceTime video functionality with both the front and rear cameras
Tap to focus on different areas to ensure focus is working properly
If all of the above checked out okay, you're good to go and can get back to snapping photos again!